8/18/2023 0 Comments Linux raspberry pi ftp server![]() You’ll also have to set permissions to ensure the drive can be accessed properly: sudo chmod 775 /usb-hdd-storage This can be found from the ‘blkid’ command. You may need to replace X with your drive ID. Now we know where our drive is, we need to mount it to the /usb-hdd-storage folder we created previously: sudo mount /dev/sdaX /usb-hdd-storage This should output the USB HDD’s label, keep a note of this.Ĭheck the boot name of the USB HDD’s partition: sudo fdisk -l Firstly check to see the partitions available on the USB HDD drive: sudo blkid Mount the USB HDD to this folder, this assumes your USB HDD is formatted as NTFS. This is where the USB HDD will be permanently mounted. The default Raspberry Pi pi user should be okay.Ĭreate a new user, used only for FTP connections: sudo adduser ftp-userĬreate a folder in /root. ![]() Login to SSH with root or a user which has sudo permissions. Note: FTP is not a secure protocol, I would recommend using SFTP for production environments. The instructions should work correctly in Debian and Raspbian too – in fact, you will probably have luck using these instructions on any Linux operating system, Raspberry Pi or not. He wrote the script below for the RPi 4 which does work.For this setup, i’m using Ubuntu 16.04 running on a Raspberry Pi 3. Shun reported that with the Raspberry Pi 4, the script above did not work. Thanks to Shun Yamashita of fulldepth for this solution to cycle the power on the Raspberry Pi 4 USB ports, which has the effect of turning the THETA Z1 on when it is plugged in with a USB cable. If you are turning it on from a power off state, see the tip below from Shun Yamashita of fulldepth. If you are trying to wake it up from sleep, there is additional information I can send. Please confirm that the camera is in a power off mode and not in sleep mode. It will be good to get more RPi project builds. There is a good body of knowledge here on the camera API, but we are not that familiar with the RPi. If you have time, please post your progress on this forum. Once you set up the network routing for each interface manually and verify that it works, then go back and create a script to automate this at startup.Īs there is a large RPi community, you can likely find detailed up for the RPi network route setup on the RPi forums. To help with configuration, you may need to plug a monitor and keyboard onto the raspberry Pi and see how the network routing is setup initially. With two network interfaces, you may need to manually set up the routes on the Raspberry Pi the first time. You will need to change the IP address of your router or set up a different router for your RPi network. If your Internet router is at the same IP address as the camera, the RPi will not be able to find the camera reliably. In this configuration, your Internet router must not be at 192.168.1.1. If you use AP mode (recommended approach to start with), then your Raspberry Pi must have two network interfaces (such as an onboard Wi-Fi plus an USB Wi-Fi adapter). If you use Client Mode, you must use Digest Authentication, which is possible, but not covered with our test application. Client Mode where the camera is assigned an IP by your Internet router.AP mode where the camera is always at 192.168.1.1.If you use the Wi-Fi API, there are two methods: If you are making a video on the server, you may want to disable topbuttomcorrection Let the community here know how it goes Other # grab all the thumbnails and write to local storageĮcho *** Will Start Upload to Digital Ocean Hosting *** # if you want to take a shot every 5 minutes # if you want to have the timelapse space 30s apartĮcho waiting 10 seconds for the next shot # increase the number 2 below to 300 to take 300 pictures ![]() # example of loop to take 2 pictures for timelapse Snippet of script - NOT the full script echo start timelapse photography loop test ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |